4 Sets Of - For Buick Chevrolet Oldsmobile Pontiac Suspension Outer Tie Rod Ends

4 Sets of - For Buick Chevrolet Oldsmobile Pontiac Suspension Outer Tie Rod Ends Every set can be described as following: Fit for 2005-2009 Buick Allure All Models 1997-2005 Buick Century All Models 2005-2009 Buick LaCrosse All Models 1997-2004 Buick Regal All Models 2000-2003 Chevrolet Impala All Models 2004-2013 Chevrolet Impala Exc. Sport Suspension 2014-2015 Chevrolet Impala Limited Exc. Sport Suspension 2000-2007 Chevrolet Monte Carlo w/o Sport Suspension 1998-2002 Oldsmobile Intrigue All Models 2004-2008 Pontiac Grand Prix All Models Package Includes: 2x Front Outer Tie Rod End-ES3459 Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts Please check above compatibility list to make sure it fits your vehicle 10 Year Warranty This item is backed by our 10-year warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only Tie-Rod End Outer Tie-Rod End Inner Tie-Rod End Some inner tie-rod ends contain a bolt and bushing. These tie-rod ends are threaded onto the rack. Since the rack is connected directly to the tie-rods, the rack replaces the center link in a parallelogram steering linkage Some inner tie-rod ends have a mirror-finished ball and a high-strength polymer bearing to ensure low torque, minimal friction, and extended life. A hardened alloy steel rod extends from the ball to the outer tie-rod end and provides maximum strength and durability Tie-Rod End Replacement Guideline: This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance 1.Lift the vehicle and dismount the front axle wheels 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes 3.Dismount the front underride guard 4.Loosen the fastening nut from the tie rod and remove it completely 5.Remove the tie rod end from the steeringknuckle using an appropriate ball joint separator 6.Remove the clamp of the bellow on the steering gear 7.Push the bellow towards the tie rod end 8.Unscrew the inner tie rod from the rack 9.Clean the sealing face of the bellow at the steering gear 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle Note:Always use new self-locking nuts and bolts for a reliable repair 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer 12.Mount the bellow and close the clamps with the appropriate special tool Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure Tip:Secure the ball stud against twisting with a suitable tool 14.Mount the front underride guard 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications 17.Perform a test drive Frequently Asked Questions (1).When to replace tie rod ends? (2).Why should I get my tie rods inspected on a regular basis? (3).Vibrations (4).Shaking (5).Wandering